REPRESENTATIVE CONCEPTSemi-Automatic Z-Stacking Machine (Pouch)
Li-ion Pouch Cell EquipmentPouch electrode Z-fold stacking.

Intended for development of pouch-cell edge and tab-region seals on a specified laminate, using material-qualified thermal and mechanical conditions.
| Technical Parameter | Indicative Configuration |
|---|---|
| Equipment type | Pouch Cell Heat Sealing Machine |
| Intended application | Pouch laminate heat sealing |
| Process principle | Opposed heated tooling applies contact and dwell to fuse the laminate sealant layer. Temperature, pressure distribution and tab-seal interfaces must be qualified; appearance alone does not prove a leak-tight joint. |
| Proposed configurations | Top/side sealing / Tab-seal tooling / Atmosphere interface |
| Laminate | Customer pouch construction and material guidance |
| Seal tooling | Matched heated jaws for selected edge/tab interface |
| Seal geometry | Application-specific length and width |
| Heating | Electric heating with temperature sensing |
| Temperature control | PID with independent overtemperature protection |
| Actuation | Manual or pneumatic clamping as selected |
| Contact load | Material-specific jaw pressure/force; no universal rating |
| Dwell | Recipe-defined heating and cooling sequence |
| Cell support | Custom fixture protecting cell stack and seal area |
| Integrity checks | Agreed seal/peel/leak method; no hermetic guarantee |
| Sizing and capacity basis | Application-specific; finalised after technical review. Relevant units: mm; °C; N; s; agreed leak/peel metric. No rating is inferred from the machine ID. |
| Control architecture | Selected process/instrument controls; integration PLC/HMI only where justified by the agreed scope. |
| Utilities and installation | Power, air/hydraulics, thermal services and exhaust only as applicable to the selected scope; site requirements confirmed in the technical offer. |
| Service and configuration changes | Accessible service interfaces and controlled tooling/recipe changes for the agreed process; cleaning/contamination requirements application-specific. |
| Safety and process limits | Hot jaws, guarding, electrolyte vapours and no hermetic guarantee. Safeguards and required conformity route need competent application-specific assessment. |
| Acceptance basis | Agreed drawings/material samples and measurable process acceptance for seal length/width; temperature; force; dwell; tab interface; integrity. Actual trials and selected-component evidence required before a performance commitment. |
Technical specifications are indicative and configurable. Final equipment parameters, performance, compatibility and supply arrangements will be confirmed following application review and detailed engineering.
Configurations are alternatives or separately selected options, not universal inclusions. Final scope depends on the actual process, materials and selected components; no capacity, precision, yield, delivery or certification is established by this listing.
Application-specific machinery combining mechanical engineering, automation integration and selected specialist subsystems. Opposed heated tooling applies contact and dwell to fuse the laminate sealant layer. Temperature, pressure distribution and tab-seal interfaces must be qualified; appearance alone does not prove a leak-tight joint. The exact selected configuration and supply feasibility are established after enquiry qualification; this is not an assertion of completed manufacture or available stock.
Research pouch closure, seal-window development and pilot assessment of laminate/tab sealing. Confirm the intended process, materials and acceptance method during application review.
Mechanical interfaces, operating mode and control requirements are defined during engineering review. Available configuration choices depend on the agreed equipment scope.
Standard and optional operations are separated in the technical offer. Specialist technology, instrumentation and safety functions require selected-equipment evidence and appropriate integration validation.
Installation scope and facility responsibilities are agreed for the actual process. No unselected utility plant, environmental-control system, process recipe or complete turnkey facility is automatically included.
Hot jaws, guarding, electrolyte vapours and no hermetic guarantee. Configurations are alternatives or separately selected options, not universal inclusions. Final scope depends on the actual process, materials and selected components; no capacity, precision, yield, delivery or certification is established by this listing. No verified performance, supplier appointment or certification is established by this catalogue entry.
A documented risk assessment, guarding review, material compatibility check and application-specific operating procedure are required before use. No CE, UL, IEC, hazardous-area approval or other certification is established by this listing. Conformity documentation depends on the agreed scope and destination requirements.
Read the Product Information Disclaimer
Request technical documentation and an application-specific configuration with your enquiry.
This listing represents an intended equipment or engineering offering. Feasibility, configuration and availability require confirmation. Please request the current engineering and supply status.
Share your materials, required capacity, process constraints and acceptance criteria. The team will review feasibility before confirming any custom scope.
REPRESENTATIVE CONCEPTPouch electrode Z-fold stacking.
REPRESENTATIVE CONCEPTPouch-cell electrolyte metering.
REPRESENTATIVE CONCEPTPouch laminate pocket forming.