LI-ION BATTERY EQUIPMENT & AUTOMATIONVADODARA, INDIA · INTERNATIONAL ENQUIRIES
AI-generated representative concept. Not a photograph of a completed Amplemech Battery Equipment & Automation machine. Pack cooling-circuit assembly and leak checks equipment family.
AI-generated representative concept. Not a photograph of a completed Amplemech Battery Equipment & Automation machine.
Pack AssemblyAMB-CSA-01Planned

Cooling System Assembly / Leak Test

Intended to coordinate assembly of a selected pack cooling circuit and verify its integrity before release, with fluid compatibility and test limits taken from the thermal-system design.

This listing represents an intended equipment or engineering offering. Feasibility, configuration and availability require confirmation.

Technical Specifications

Cooling System Assembly / Leak Test — indicative configuration
Technical ParameterIndicative Configuration
Cooling-circuit typeSelected coolant circuit, plate, piping or assembly
Component dimensionsApplication-specific component envelope (mm)
Test volumePart/internal fixture volume (L) defined for test method
Test mediumClean dry air for proposed pneumatic leak test; other media separately reviewed
Pressure rangeTest pressure (kPa/bar) limited by customer part rating
Gauge/absolute pressure referenceGauge/absolute reference stated explicitly in final test recipe
Leak-test principlePressure-decay/differential-pressure instrument as selected
Leak acceptance unit and limitCustomer-approved Pa/s or calibrated flow unit/limit with reference conditions
Pressure regulatorRegulated supply with suitable isolation and protection
Leak sensor/instrumentSelected leak instrument; range/precision confirmed from actual datasheet
Stabilisation timeProgrammable; established from volume, pressure and thermal behaviour
Test durationProgrammable; validated against agreed reference leakage
Temperature compensation, where requiredTemperature control/compensation where validated by selected method
Fixture interfaceApplication-specific nest and circuit connections
Sealing connectorsCompatible quick-connect or engineered sealing interface
Part clampingManual standard; powered clamps optional with safeguards
Manual/automatic loadingManual loading standard; assisted handling optional
Test sequenceFill, stabilise, isolate, measure and vent sequence for selected method
Pass/fail judgementApproved threshold and invalid-test/fault handling
Data recordingOptional test/recipe/result recording
Barcode/part IDOptional part ID/barcode association
Electrical supplySelected instrument/controller supply
Pneumatic supplyAir quality/pressure/flow defined for selected circuit
Pressure relief and protectionPressure relief, rated components, guarded clamping and safe venting
Calibration/reference leak requirementsReference leaks/standards and documented calibration/verification procedure

Technical specifications are indicative and configurable. Final equipment parameters, performance and supply arrangements will be confirmed following application review and engineering evaluation.

Proposed model configurations

ModelConfiguration
AMB-CSA-01-MCooling-circuit assembly fixture
AMB-CSA-01-APneumatic pressure-decay leak-test station
AMB-CSA-01-CCombined assembly and leak-test station

An assembly fixture does not automatically include leak testing. Air-based leak tests and liquid proof tests are different scopes. Leak thresholds, pressure, calibration, timing and thermal effects require a defined part and validated recipe; no IP rating is implied.

Intended operating principle

Application-specific solutions combine mechanical engineering and automation integration with selected specialist subsystems. The proposed solution families are Cooling-circuit assembly fixture; Pneumatic pressure-decay leak-test station; Combined assembly and leak-test station. Configuration, acceptance and supply feasibility are established for the enquiry; this listing does not establish completed models or current stock.

Principal applications

Pack cooling-loop assembly, connection-process trials and enclosure/circuit integrity verification. Confirm the intended process, materials and acceptance method during application review.

Configuration & integration

Mechanical interfaces, operating mode and control requirements are defined during engineering review. Available configuration choices depend on the agreed equipment scope.

  • Cooling-circuit assembly fixture
  • Pneumatic pressure-decay leak-test station
  • Combined assembly and leak-test station

An assembly fixture does not automatically include leak testing. Air-based leak tests and liquid proof tests are different scopes. Leak thresholds, pressure, calibration, timing and thermal effects require a defined part and validated recipe; no IP rating is implied.

Utilities & installation

Power, communications and any compressed-air requirements depend on the selected components and agreed site interfaces. Utilities and installation responsibilities are confirmed during technical review; optional modules are not standard inclusions.

Engineering & safety considerations

Coolant compatibility; cleanliness. An assembly fixture does not automatically include leak testing. Air-based leak tests and liquid proof tests are different scopes. Leak thresholds, pressure, calibration, timing and thermal effects require a defined part and validated recipe; no IP rating is implied. Application-specific risk assessment, safeguards and acceptance validation are required before operation.

A documented risk assessment, guarding review, material compatibility check and application-specific operating procedure are required before use. No CE, UL, IEC, hazardous-area approval or other certification is established by this listing. Conformity documentation depends on the agreed scope and destination requirements.

Read the Product Information Disclaimer

Typical engineering workflow

  1. Define the input materials, geometry and process objective.
  2. Agree the configuration, interfaces and safety requirements.
  3. Establish a trial plan and measurable acceptance criteria.
  4. Confirm technical scope before a quotation or delivery commitment.

Technical documentation

Request technical documentation and an application-specific configuration with your enquiry.

Questions about this equipment

Is this equipment available for immediate delivery?

This listing represents an intended equipment or engineering offering. Feasibility, configuration and availability require confirmation. Please request the current engineering and supply status.

Can the configuration be adapted to our application?

Share your materials, required capacity, process constraints and acceptance criteria. The team will review feasibility before confirming any custom scope.

Continue exploring

Related equipment